remove agitator from Maytag commercial technology washer

By Admin 10 months ago

remove agitator from Maytag

Views: 489 / 10 months ago

How to remove the agitator from Maytag commercial technology washer

This how-to removes the agitator from Maytag commercial technology washer. You will need Wrenches and assorted sockets and ratchets, a flathead screwdriver.

Pennies stuck under Maytag Centennial Washer. How do I remove a Penn?

This how-to removes the agitator from Maytag commercial technology washer. You will need Wrenches and assorted sockets and ratchets, a flathead screwdriver. Tyler, I left his agitator up. No coins (darn) But when you close the lid select start the sensing light shines and the washer makes a really loud screeching noise throughout the sensing cycle. List some useful books/tips to follow to get more ideas? Either your actuator below the tub will fail and need replacing or the pulley beneath the gear case will be loose. The actuator can be removed using this link. All checks are correct then replace them. Actuators. Click here to watch the video How to Remove The. Activator and how to remove the agitator from Maytag commercial technology washer.



How do I remove the agitator from a Maytag Washer?

STEP 1

Disconnect the power supply. Make sure the washer is unplugged before continuing with this how-to.

TIP Somehow-sot will say how you can set the machine to spin and pull the agitator out. However, some how-to's state you need 'special tools' to pop it out and those extra special tools remain a mystery.

STEP 2

Remove the belt. I usually do this by removing a tensioner pulley and then releasing the tension on the belt. You may find it easier to remove the plastic cover that protects the mechanism (if your how-to comes with such a decorative piece).

STEP 3

Remove the agitator. There are four bolts holding this baby down. two nuts and two bolts. You can see them through holes in one of those decorative plastic panels.

STEP 4

At this point, you have the agitator off now. How do I get it back on so it spins?

You will need to read however many how-toss on how to remove the agitator from a Maytag Washer until you find one that tells you how to reassemble.

Hopefully, this how-to was of use to you how to remove the agitator from Maytag commercial technology washer.



Maytag agitator removal tool

On a Maytag-equipped washing machine, the agitator contains two long shafts spun by an electric motor. The agitator consists of 3 main pieces: 1) Lower part (2) Middle piece (3) Top portion (segmented bowl).

At the very top center of the agitator is a large plastic keel nut. This houses a metal locking mechanism that can be released with just a small turn to open up the entire hub assembly which holds the spindle and bearings for both lower parts as well as each half of the middle segmented bowl. Once removed from its hub, each half will become free to slide off its respective shaft. Finally, you have access to all areas previously reserved by these pieces now removed. Know how to remove the agitator from Maytag commercial technology washer.

The Maytag agitator removal tool consists of a plastic "T" handle with a magnetic center to grab onto the keel nut. A cog on one end allows for precision turning via its teeth which mesh with the inner ring on the keel nut making it easy to unscrew by hand or very gently with a set of pliers if necessary.

Assembling this back is simply putting each half back upon its respective shaft. The lower parts are plastic, so they cannot be cross-threaded as long as you're careful about lining up the slots in their respective middle pieces that slide into place. Once you have both halves fully assembled then insert it into the washing machine and tighten the keel nut back into place.

Pennies stuck under Maytag Centennial Washer. How do I remove a Penn?

This tool is often sought out by people who just want to mix up a small load of laundry or if they're doing a smaller than usual load and don't want to waste the umph necessary for an entire spin cycle on just a couple of items. How to remove the agitator from Maytag commercial technology washer.

Note: If you should find yourself in need of agitator removal because your spinning basket has been ripped from its housing, you must instead use the older metal locking mechanism located directly under where the lower half was removed. This can be done relatively easily with an adjustable wrench to turn this "L" shaped rod until it releases from inside its internal threaded shaft hole. Once unscrewed by hand, simply lift up your old agitator and you'll see where this rod was once inserted. You can then insert it back in its threaded hole in the lower agitator, turn a quarter turn to secure it in place, and replace your agitator. For how to remove the agitator from Maytag commercial technology washer.

Of course, this tool also has many other uses including arcade joystick repair among others which I will cover more extensively soon. Just wanted to show an example of what can be done with such a tool rather than just leaving you hanging without naming any of the possible purposes of having one on hand.

Read More: How to connect the scanner to computer your daily need

 

The problem & Solutions

My Maytag Bravos XL washer has several problems. One is that when the machine is turned on, it fills with water, and then after 10 or 15 seconds, it stops filling. It won't pump the water out either (and doesn't drain). The entire time this is happening there's a loud "thumping" noise coming from inside the machine. I've researched this issue online and found many people who have their machines quit in exactly in my situation; they seem to think that there's something stuck inside which causes the thumping sound (a sock, perhaps?) but no one seems to be able to actually fix the problem. So naturally, I'm thinking that it must be something else since nobody has managed to solve this issue on their own. Know how to remove agitators from Maytag commercial technology washers.

Another problem is that the machine doesn't drain all the way, so there's always a small puddle of water in it even after draining. This seems like an easy fix (the rubber hose coming out of the pump needs to be replaced)--but this is clearly not what's causing my first issue of no water being pumped out. But I am unaware if I can solve both problems with one part replacement or if I will need two separate parts?

The Maytag website lists two different replacement parts for Bravos XL models. Since they're listed separately, maybe these are not related issues? The symptom is that the machine won't pump out the water. I've included a couple of photos that show where I'd like some help identifying what part(s) my machine is having trouble with and which parts (if any) will fix both my problems:

.